Free tool · geometry only

Labels per roll calculator: roll diameter, labels and rolls

This labels per roll calculator works out the roll diameter for a number of labels, how many labels fit inside the largest roll your printer or applicator takes, and how many rolls a run needs. A roll of 1,000 labels that are 50 mm long with a 3 mm gap, wound on a 76 mm core with a 3 mm wall, using label plus backing 0.15 mm thick, comes to an outside diameter of about 129.8 mm, with 53 metres of material on the roll; 25,000 labels would need 25 rolls.

  • Three modes, including thickness from a roll you already have
  • Roll drawn to scale, shareable link
  • Send the roll spec straight into a quote request
  • ICO registered ZA810991
  • UK company 11135452
  • Rules checked 18 November 2026
Free quotes

Get quotes for your roll labels

Free, no obligation. Three quick steps.

Your labels
The spec
Your details

ICO registered ZA810991 No obligation For businesses

Free calculator · geometry only

Labels per roll and roll diameter

Enter your own figures. Nothing is sent anywhere unless you choose to add the result to a quote request.

1The label

Length is the label's size along the roll (the direction it comes off). Gap is the space between labels.

2The core and material

Measure it, ask your supplier, or use "Thickness from a roll I have".

3The roll

129.8 mm roll diameter
1,000labels per roll
53 mmaterial on the roll
25rolls for your total

Repeat 53 mm × 1,000 labels = 53 m. Diameter = √(core outside² + 4 × length × thickness ÷ π).

129.8 mm

Drawn to scale: the mint ring is the roll's outside edge, the light ring the core.

Labels per roll calculator: key points
  • A roll of 1,000 labels that are 50 mm long with a 3 mm gap, wound on a 76 mm core with a 3 mm wall, using label plus backing 0.15 mm thick, comes to an outside diameter of about 129.8 mm, with 53 metres of material on the roll; 25,000 labels would need 25 rolls.
  • Roll diameter = √(core outside diameter² + 4 × length on the roll × label-and-backing thickness ÷ π). Length = rows of labels × (label length + gap).
  • Diameter grows with the square root of the length, so doubling labels per roll makes the roll about 1.4 times as wide (above the core), not twice.
  • Thickness is the figure most people don't know: measure a roll you already have (labels, outside diameter, core) and the calculator works it out.
  • Results are geometry only: real rolls vary with winding tension, liner and materials, so leave a margin under your equipment's maximum diameter.
  • Shareable links: ?mode=od|count|measure&w=&h=&gap=&across=&core=&wall=&t=&labels=&od=&total= set the inputs and show the result on load.

Labels per roll at a glance

Short answer

Common label sizes on 76 mm and 25 mm cores, using a 0.15 mm label-plus-backing thickness as an example. Change the thickness to match your material: the results move with it.

Generated by the calculator's own code on 18 November 2026. Example inputs: 0.15 mm label + backing thickness; core wall as shown. Geometry only; real rolls vary.
LabelCoreLabels per rollRoll diameterMaterial on rollRolls for 10,000
50 × 25 mm label (25 mm along the roll), 3 mm gap76 mm core, 3 mm wall1,000109.9 mm28 m10
100 × 50 mm (50 mm along), 3 mm gap76 mm core, 3 mm wall1,000129.8 mm53 m10
100 × 150 mm shipping label, 3 mm gap76 mm core, 3 mm wall500146.1 mm76.5 m20
100 × 150 mm shipping label, 3 mm gap25 mm core, 1.5 mm wall500124.1 mm76.5 m20
60 × 40 mm (40 mm along), 3 mm gap, 2 across76 mm core, 3 mm wall2,000122.2 mm43 m5
100 × 50 mm (50 mm along), max roll 200 mm76 mm core, 3 mm wall3,287200 mm174.21 m4
100 × 50 mm (50 mm along), max roll 125 mm40 mm core, 2 mm wall1,352125 mm71.66 m8

How is the roll diameter calculated?

Short answer

The end of a roll is a ring. Its area, π × (outside diameter² − core outside diameter²) ÷ 4, equals the length of material wound on multiplied by its thickness. Rearranged, the outside diameter = √(core outside² + 4 × length × thickness ÷ π).

  1. RepeatLabel length along the roll + gap.
  2. RowsLabels per roll ÷ labels across, rounded up.
  3. LengthRows × repeat.
  4. Core outsideCore inside diameter + 2 × wall.
  5. Diameter√(core outside² + 4 × length × thickness ÷ π), rounded to 0.1 mm.

For the other direction (labels that fit a maximum diameter), the length is π × (maximum diameter² − core outside²) ÷ (4 × thickness), and the number of rows is that length ÷ repeat, rounded down. To work out thickness from a roll you have, the same formula is solved for thickness. Rolls needed = total labels ÷ labels per roll, rounded up.

What inputs, assumptions and limits does it use?

Short answer

Inputs are all yours: label length along the roll, gap, labels across, core inside diameter and wall, label-plus-backing thickness, labels per roll or maximum diameter, and total labels. It assumes tight, even winding with no leader or trailer.

Roll spec sorted?Send it with your label details and a specialist UK label printer will quote.
Get quotes

How do I find the thickness of my labels?

Short answer

Ask your supplier for the face material plus liner caliper, or measure a roll you already have: count or read the labels on it, measure its outside diameter and the core, and use the 'Thickness from a roll I have' mode.

A quick check: the calculator's thickness mode gives the combined label-and-backing thickness, which is the figure the other modes need. Measure across the roll's widest point, and use a full roll, not a part-used one.

How do I use the results when ordering labels?

Short answer

Put the labels per roll, core size and maximum roll diameter in your brief, with the label size, gap, wind direction and total quantity. The button under the result adds the spec to the quote form for you.

Printers often quote labels per roll in round numbers. If the calculator shows that 1,140 labels fit your applicator's maximum roll, asking for 1,000 per roll leaves a margin and keeps counting simple.

Get quotes for your labels

Tell us about the labels once. We pass your brief to a specialist UK label printer suited to your job, who will:

  • Check the spec with you: size, material, adhesive, finish, roll or sheet, and how the labels will go on.
  • Quote in writing for your quantity, with any set-up, plate or proof costs shown.
  • Proof before printing, so you can check the artwork and the legal text.

For business orders. Prefer email? Write to [email protected] with your label size, quantity and what they're for.

Free quotes

Tell us about your labels

Three quick steps. Free and no obligation.

Your labels
The spec
Your details

ICO registered ZA810991 No obligation For businesses

Labels per roll calculator: frequently asked questions

How do you calculate labels per roll?

Work out the length of material that fits on the roll: π × (maximum roll diameter² − core outside diameter²) ÷ (4 × label-and-backing thickness). Divide by the label length plus gap to get rows, and multiply by the number of labels across.

How do you calculate the diameter of a label roll?

Outside diameter = √(core outside diameter² + 4 × length × thickness ÷ π), where length is the number of rows of labels × (label length + gap) and thickness is the label plus its backing.

What thickness should I use?

The combined thickness of the label and its backing liner. Ask your supplier, or measure a full roll you already use and let the calculator work it out in the 'Thickness from a roll I have' mode.

How many labels are on a 76 mm core roll?

It depends on the label length, gap, thickness and the maximum roll diameter. For example, the at-a-glance table shows how many 50 mm labels with a 3 mm gap fit on a 200 mm roll at 0.15 mm thickness.

Why doesn't doubling the labels double the roll size?

Because roll diameter grows with the square root of the length wound on. Doubling the length makes the wound part of the roll about 1.4 times as big, not twice.

Is the result exact?

It's geometry and assumes even, tight winding with the same thickness throughout. Real rolls vary a little, so leave a margin under your equipment's maximum and ask the printer to confirm.

Can I share my calculation?

Yes. The link under the calculator includes all your inputs as URL parameters (mode, w, h, gap, across, core, wall, t, labels, od, total), so anyone opening it sees the same result.

Does the calculator store my data?

No. It runs in your browser. Nothing is sent unless you choose to add the result to a quote request and send the form.

Sources

This tool uses geometry only (the area of a ring), with figures you enter. No outside data, rates or prices are used; the method is set out above.