Label type guide

Roll labels: how to specify them so they run first time

Roll labels are labels supplied on a continuous backing (the liner) wound around a cardboard core, ready for a hand dispenser, an automatic applicator or a thermal printer. Getting them to run first time comes down to five details: label size and gap, core size, maximum roll diameter, labels per roll and wind direction. This guide explains each one.

  • Core, roll diameter and wind direction explained
  • Labels per roll and rolls needed, worked out for you
  • Spec for applicators, dispensers and printers
  • ICO registered ZA810991
  • UK company 11135452
  • Rules checked 18 November 2026
Free quotes

Get quotes for roll labels

Free, no obligation. Three quick steps.

Your labels
The spec
Your details

ICO registered ZA810991 No obligation For businesses

Roll labels: key points
  • A roll label spec has five numbers a printer needs: label width and height, the gap between labels, the core's inside diameter, the largest roll diameter your equipment takes, and the labels per roll.
  • Wind direction says whether labels face out or in, and which edge comes off first. Automatic applicators often need a particular wind, so get it from the machine's manual or supplier.
  • Rolls are usually the right choice for machine application, thermal printers and anything applied by hand in volume; sheets suit small batches printed on an office printer.
  • Labels per roll is a trade-off: bigger rolls mean fewer changeovers, but the roll has to fit on your applicator or printer.
  • Choose the face material and adhesive for where the label lives (fridge, freezer, bathroom, warehouse), not just for how it looks.
  • Our labels per roll calculator turns your label size, gap and core into labels per roll, roll diameter and rolls needed.

What are roll labels?

Short answer

Self-adhesive labels on a continuous liner, wound onto a core. The waste around each label (the matrix) is usually stripped away, so labels peel off one by one in a dispenser, applicator or printer. They can be fully printed, part-printed for over-printing in-house, or blank.

Printed product labels

Your artwork, printed by the label printer, for jars, bottles, boxes and tubs.

Blank labels for thermal printers

Plain labels you print yourself with barcodes, addresses or dates.

Part-printed

Branding printed in advance, with a clear panel for in-house batch codes or dates.

Machine-applied

Wound and sized to run on an automatic label applicator on your line.

What details does a roll label spec need?

Short answer

Label width and height (and which way the label travels off the roll), the gap between labels, how many labels across the roll, the core's inside diameter, the maximum outside diameter of the roll, the number of labels per roll and the wind direction. Add the material, adhesive and finish, and the total quantity.

Label sizeWidth × height in mm, and which dimension runs along the roll (the feed direction).
GapThe space between labels on the liner, often a few millimetres; your printer or applicator may need a minimum.
Labels acrossOne label across the web, or two or more side by side for some printers.
Core sizeThe inside diameter of the cardboard core, to fit your dispenser, printer or applicator spindle.
Max roll diameterThe largest outside diameter your equipment can hold.
Labels per rollFixed by the roll size, or chosen for convenience, such as 500 or 1,000 per roll.
Wind directionFace out or face in, and which edge leads off the roll.
Material and adhesivePaper or film, permanent, removable or freezer adhesive.

Cores come in several inside diameters (25 mm, 40 mm and 76 mm, roughly 1 inch to 3 inches, are among the common sizes), and desktop and industrial equipment often take different ones. Measure your existing rolls, or check the manual, rather than guessing. Then use our labels per roll calculator to check the roll will fit.

What does wind direction mean on a label roll?

Short answer

It describes how the labels sit on the roll: wound out (printed face outwards) or wound in (face towards the core), and which edge of the label comes off first: top, bottom, left or right. Many printers number these positions, but the numbering isn't the same everywhere, so send a diagram or photo.

Wound out (face out)Wound in (face in)
Face out vs face in. Combined with the leading edge (top, bottom, left or right first), this gives eight possible winds.

How many labels fit on a roll?

Short answer

It depends on the label length plus gap, the thickness of the label and liner, the core, and the largest roll your equipment takes. Roll diameter grows with the square root of the length wound on, so doubling the labels per roll doesn't double the diameter.

The calculation is geometry: the area of the roll end (outside circle minus the core) equals the length of material wound on multiplied by its thickness. We've built it into a free labels per roll calculator: enter the label length, gap, labels across, core and thickness to see the roll diameter for a given count, or the most labels that fit in a maximum diameter, and the number of rolls a run needs.

Thickness is the one figure people rarely know. Measure a roll you already use (count the labels, measure the outside diameter and the core) and the calculator can work back to the thickness.
Ready to price your labels?Send one brief and a specialist UK label printer will come back with a quote.
Get quotes

When are roll labels better than sheet labels?

Short answer

When labels go on by machine, come off a thermal printer, or are applied by hand in any volume. Sheets suit small numbers you print yourself on a laser or inkjet printer.

Choose rolls when

  • You use an automatic applicator or a hand dispenser
  • You print barcodes, dates or addresses on a thermal printer
  • You use hundreds or thousands of labels at a time
  • You want the label printer to print the full design

Choose sheets when

  • You print a few labels at a time on an office printer
  • Designs change constantly in tiny quantities
  • You don't have a dispenser or applicator
  • Labels are a temporary, short-run need

Which material and adhesive should roll labels use?

Short answer

Paper for dry, short-life uses; film (such as polypropylene or polyester) for wet, chilled, oily or handled products; and an adhesive matched to the surface and temperature. Tell the printer what the label sticks to and what it has to survive.

General guidance; always test samples on your own packaging
Where the label goesAsk the printer about
Dry boxes, cartons and bagsStandard paper with a permanent adhesive
Fridges, condensation, iceFilm face material and an adhesive for cold or damp surfaces
FreezersFreezer-grade adhesive, applied at the temperature the printer specifies
Bathrooms, oils, cosmeticsFilm with a laminate or varnish to protect the print
Curved or squeezable containersConformable film that flexes without lifting
Returnable crates and temporary useRemovable adhesive that peels cleanly
Hazard labels on chemicalsMaterials that stay firmly fixed and legible (CLP Article 31)

How do you brief a label printer for roll labels?

Short answer

Send the label size and shape, total quantity and number of designs, material and finish, the roll spec (core, maximum diameter, labels per roll, wind) and how the labels are applied, plus your deadline. Our quote form asks for exactly these.

  1. MeasureLabel size, gap, and an existing roll's core and diameter.
  2. Check your equipmentCore size, maximum roll diameter and wind from the manual.
  3. Size the rollsUse the calculator to set labels per roll and rolls needed.
  4. Send the briefThrough our form: we pass it to a specialist UK label printer.
  5. Approve a proofAnd ask for samples to test on your line.

Get quotes for your labels

Tell us about the labels once. We pass your brief to a specialist UK label printer suited to your job, who will:

  • Check the spec with you: size, material, adhesive, finish, roll or sheet, and how the labels will go on.
  • Quote in writing for your quantity, with any set-up, plate or proof costs shown.
  • Proof before printing, so you can check the artwork and the legal text.

For business orders. Prefer email? Write to [email protected] with your label size, quantity and what they're for.

Free quotes

Tell us about your labels

Three quick steps. Free and no obligation.

Your labels
The spec
Your details

ICO registered ZA810991 No obligation For businesses

Roll labels: frequently asked questions

What are roll labels?

Self-adhesive labels on a continuous backing liner wound around a core, so they can be peeled off one at a time by a dispenser, an automatic applicator or a thermal printer. They can be printed with your design, part-printed or blank.

What core size do I need for label rolls?

The core's inside diameter has to fit your dispenser, printer or applicator. Common sizes include 25 mm, 40 mm and 76 mm, and desktop and industrial equipment often take different ones. Check the manual or measure a roll that already fits.

How many labels are on a roll?

It depends on the label length and gap, the thickness of the label and liner, the core and the maximum roll diameter your equipment takes. Our labels per roll calculator works it out from those figures.

What is label wind direction?

Whether labels are wound face out or face in, and which edge comes off the roll first. Automatic applicators often need one specific wind, so give the printer the wind your machine needs, ideally with a diagram or photo.

Are roll labels cheaper than sheet labels?

It depends on quantity and spec, so we don't quote prices. Rolls are usually the practical choice for machine application, thermal printing and larger quantities; compare written quotes for the same spec.

Can I print my own roll labels?

Yes, with a thermal transfer or direct thermal label printer and blank or part-printed labels on a roll. Check the core size, maximum roll diameter and whether your printer needs a ribbon.

What is the gap between labels on a roll?

The space between one label and the next on the liner. Printers use it to detect where each label starts, and applicators need it to separate labels cleanly, so match the gap your equipment expects.

Can roll labels be used on curved bottles?

Yes, with the right size, shape and a conformable face material. Tell the printer the container's diameter and any taper, and test samples.

Sources

We checked the facts on this page against these sources on 18 November 2026. Rules change: check the current version before you sign off a label.

  1. Food labelling: giving food information to consumers (GOV.UK, Defra and FSA)
  2. CLP Article 31: general rules for the application of labels (legislation.gov.uk)
  3. Green Claims Code: environmental claims on goods and services (GOV.UK, CMA)